Skip to content
Calls answered 24/7Office Mon–Fri 8am–5pm
6717 4th Ave, Brooklyn, NY 11220718-439-1224
Commercial Laundry SolutionsNew York · Since 2001

Error code library

Maytag Commercial error codes

Maytag commercial machines use several code systems. MAH (Neptune) front-load washers save the last three help codes in diagnostics as 1h.xx, 2h.xx and 3h.xx. Older Maytag washers and stack dryers show d-codes when you enter setup mode, MXT washers light a fault number from 1 to 8, and MFR washer-extractors show D and H messages on the graphic display.

Covers: Maytag MAH-series and MXT commercial front-load washers, Maytag stack and single dryers, MFR washer-extractors.
Based on: Maytag MAH washer help codes service sheet, Maytag commercial washer and dryer service manuals (diagnostic and help modes), MXT washer fault messages and MFR washer-extractor programming manual.

Help codes

Motor locked rotor

The motor is not turning in wash steps.

  • Technician: check for drag, belt and motor.

Motor not turning in spin / speed not available

Spin did not reach the requested speed.

  • Technician: check motor, belt and control.

Unbalance in spin

Unbalance detected at different spin speeds; code 32 means the final spin was aborted.

  • Redistribute the load.
  • Check the machine is level.

Suds lock or overload

Too many suds or too large a load.

  • Use HE detergent in the right amount and do not overload.

Door not locked at end of final spin

Door lock problem.

  • Technician: check the door lock.

Slow fill

Water level dropped after fill, or it took longer than 4 minutes to reach level.

  • Check water supply and inlet screens.

Drag above 650 RPM

Often clothing caught in the door boot.

  • Check the door boot for trapped items.

Slow drain

Water level still seen at the start of spin.

  • Check the drain pump and drain hose for blockage.

Motor speed or power limit errors

Motor ran too fast, too long at power limit, or kept running after coast-down.

  • Technician: run motor checks and check belt tension.

Motor running with door unlocked

Motor above 85 RPM while the door is not locked, likely electrical noise.

  • Technician: check wiring and grounding.

Debit card reader messaging

Communication problems between the card reader and control.

  • Check reader connections; power cycle.

Older washer diagnostic codes (setup mode)

Door sense error

Washer door sense error on the control board, or power line interference. Cycles are disabled until cleared.

  • Technician: check the door switch and wiring, then clear the code.

Coin drop blocked

Coin drop 1 (d5) or coin drop 2 (d13) is blocked or its circuit failed.

  • Clear the coin chute and empty the coin box.
  • Check the coin drop switch.

Slow fill

Slow fill in the previous cycle. The cycle paused but can be restarted.

  • Check water supply and inlet screens.

Slow drain

The last drain was slow.

  • Check the drain pump or valve and drain hose.

Low voltage

Supply voltage below about 185 VAC for 8 seconds.

  • Technician: check supply voltage and connections.

Door lock sense error

Door lock sense problem or power line interference.

  • Technician: check the door lock and wiring.

Motor overtemp or overcurrent

The cycle paused because the motor overheated or drew too much current.

  • Do not overload.
  • Technician: check motor, belt and drag.

No debit card reader communication

The washer is not getting communication from the installed debit card reader.

  • Check the card reader connection and power.

Stack dryer diagnostic codes (setup mode)

Thermistor circuit error

Lower (d2) or upper (d18) dryer thermistor circuit error on the control. That pocket is disabled until cleared.

  • Technician: check the thermistor and its wiring.

Temperature too high

Lower (d3) or upper (d19) dryer got too hot.

  • Clean lint screens and exhaust.
  • Technician: find the cause before clearing.

Motor control circuit error

Lower (d4) or upper (d20) motor control circuit error.

  • Technician: check the motor relay and wiring.

Coin drop blocked

Coin drop 1 or 2 blocked or its circuit failed.

  • Clear the coin chute.

Low voltage

Voltage below about 90 VAC for 8 seconds.

  • Technician: check supply voltage.

Motor sense circuit error

Lower (d12) or upper (d14) motor sense circuit error.

  • Technician: check the motor and sense wiring.

Motor running when it should be off

Lower (d21) or upper (d22) motor sensed running when it should be off. Check for line noise or harness problems.

  • Technician: check wiring harness and relays.

Control not calibrated

The control board is not calibrated for thermistors.

  • Technician: replace the control board.

washer fault codes (1–8)

Drain failure

The washer did not see an empty level within 30 seconds of a drain step.

  • Check for a slow or blocked drain.

Out of balance

The load could not be balanced.

  • Redistribute the load.

Motor overload

Open circuit in the motor current overload, motor thermal overload or door-closed switch circuit.

  • Technician: check those circuits and connections.

Door lock failure

The door-locked switch circuit opened after the cycle started, often a failed bi-metal lock device.

  • Technician: check the door lock assembly.

Fill failure

Full level not reached within 10 minutes.

  • Check fill hose screens, water pressure, drain valve, air dome and water valves.

Heating / temperature sensor failure

Problem in the temperature sensor circuit.

  • Technician: check sensor connections, polarity and the probe.

Coin input fault

The coin switch is held open by a jammed coin, full coin box or a wiring issue.

  • Clear the coin meter and empty the coin box.

Memory failure

Memory scrambled by power line noise or programming.

  • Power down; if it persists, reprogram all steps.

MFR washer-extractor diagnostic and help messages

Water level / temperature sensor defective

The level or temperature sensor is defective. Can only be cleared by loading factory settings and cycling power.

  • Technician: replace the sensor, then reload settings.

Door switch and lock faults

Door sense, unload, lock solenoid, lock check at start or bi-metal lock failures.

  • Technician: check the door switches, lock solenoid and bi-metal lock.

Slow fill / slow drain

Fill or drain took too long.

  • Check water supply and the drain.

Overfill

Water went above the allowed level.

  • Technician: check the inlet valves and level sensor.

Tilt / out of balance

Out of balance before spin, in normal spin or at high spin.

  • Redistribute the load.
  • Technician: check the tilt switch and suspension.

Too hot / overflow

The water is too hot or overflowed.

  • Technician: check the heating control and inlet valves.

No spin speed signal

No motor speed signal during spin.

  • Technician: check the speed sensor and inverter.

Inverter faults

Inverter error, time-outs, or the inverter is not loaded with the correct parameters (H63 / H64). Do not run the machine until a technician checks it.

  • Technician: check and reload inverter parameters.

Card reader messaging

The card reader communication went out of sequence.

  • Check the card reader and its connection.

These explanations are general guidance written by CLS from manufacturer service documentation, and code meanings can vary by control version. Always confirm with the manual for your exact model. Disconnect power (and gas or steam) before opening any panel. Repairs inside the machine should be done by a qualified technician.

← All brands · Preventive maintenance checklists

Still showing the code?

Our factory-trained technicians service Maytag Commercial equipment across New York every day. Calls answered 24/7.